Electric mirrors for mk1 Aygo

[flash22]

To swap base you need to pop the cover off the base to access the mount and pull the cable back through

[Colin J.S]

On 2/28/2022 at 2:48 PM, flash22 said:

All the logic is in the mirror switch, no they are not all the same  most of the cars use the same switch gear tho - its 8 wires to the mirrors my mistake

 

Not sure if it can be done on the mk2 as the mirrors are different, that's something you will need to figure out

i did a thread on the yaris switch change

diagrams, you can use the IQ, Yaris or Auris ones i have all 3 types

the simplest diagram i have

 

Hi, Thanks for help so far, is there a diagram that shows the wiring colours and or shows a 'key' to what the lettering means please 

[flash22]

The first diagram i posted is for the 28 pin type, have you got the switch if so what type

@PetrolDave yes there is a 24 pin switch with folding mirrors - rav4 2015 on not sure if the plug is the same

eg.

https://www.ebay.co.uk/itm/31388573046

https://www.ebay.co.uk/itm/144227093165

[Colin J.S]

40 minutes ago, flash22 said:

The first diagram i posted is for the 28 pin type, have you got the switch if so what type

@PetrolDave yes there is a 24 pin switch with folding mirrors - rav4 2015 on not sure if the plug is the same

eg.

https://www.ebay.co.uk/itm/31388573046

https://www.ebay.co.uk/itm/144227093165

Its an IQ 2010 switch with 9 pins not sure if link will work as I bought it https://www.ebay.co.uk/itm/192342319805

[Colin J.S]

The ad says part no, 183575 

[flash22]

IQ mirror diagram.pdf

[Colin J.S]

32 minutes ago, flash22 said:

IQ mirror diagram.pdf 51.96 kB · 0 downloads

Thank you very much indeed 🙂

 

[Colin J.S]

 Next question...how does the mirror separate from the base plate? 

[flash22]

Cover on the bottom of the base (the part on the car) ??

[Colin J.S]

3 minutes ago, flash22 said:

Cover on the bottom of the base (the part on the car) ??

It comes off the car as in pic, there is no removable cover on the underside 

[flash22]

Is there anything down the centre where the control cables go ? if you fold the mirror does the centre move

[Colin J.S]

5 minutes ago, flash22 said:

Is there anything down the centre where the control cables go ? if you fold the mirror does the centre move

where the cables go through the slightly grey ring stay still and the mirror pivots around it if that makes sense 

[flash22]

The collar has 2 notches in it, it may unscrew - as this is the one off your car i would be extremely wary of forcing anything

[flash22]

any progress on this project ??

[Colin J.S]

4 hours ago, flash22 said:

any progress on this project ??

A little. Got messed around buy an eBay seller and had to fight for a refund, then buy mirrors elsewhere. Managed to get the mirror off the base plate. The IQ mirror has a cover plate revealing 3x screws so was easy. However it simply won't go on the Aygo base plate. I thought, I could cut an access hole in the Aygo plate, then glue the piece back in as its out of sight but 2 problems, 1, the hole in the aygo plate is too large so nothing to bolt the new mirror to, 2, even if it had fitted, the angle/shape of the aygo plate would prevent the new mirror from folding in.

Plan B - use the IQ base plate but of course its smaller and the triangle is a different angle. One lower bolt lines up but not the other 2 so I'm going to have to improvise somehow. the leading edge is tight to the front wing but doesn't touch or rub, so I can live with that. There is about a 1'' gap below the mirror but I guess I find or make a piece of trim to hide it.couple of pics show a test fit, you can see the top sticking out where it only has on bolt at the moment. I think I might use a coach bolt through near the top, not perfect but it will be discreet enough. I dont think anyone would notice unless they knew, if that makes sense.

 

[flash22]

How does it line up when aligned with the bottom of the door rather than the top of the door ?

[Colin J.S]

13 minutes ago, flash22 said:

How does it line up when aligned with the bottom of the door rather than the top of the door ?

I will look into the idea, I ran out of time yesterday and was getting a bit stressy with it, then of course it's been tipping it down all day today ....In theory if it lines up at the bottom and I can manage to bolt it on, then as for the gap at the top, I could probably cut a section from the original base plate ....I will have a look as soon as its dry and I have time 🙂

 

[flash22]

👍 got it in one, if the mirror is secure the top the trim is purely cosmetic, it can be trimmed, bonded/plastic welded and body worked then either painted or textured (U-pol PlastX)

[Colin J.S]

1 hour ago, flash22 said:

👍 got it in one, if the mirror is secure the top the trim is purely cosmetic, it can be trimmed, bonded/plastic welded and body worked then either painted or textured (U-pol PlastX)

Thats easy to say ,,,its the fixing points that will be compromised...how I had it....its the lowest fixing point that lined up ....higher points will need to be fabricated ...how? 

[flash22]

If you look at the back of the  base there are 3 holes what the screws go in to these are also heat stakes that hold a cover on, the base its self should be hollow, it has to be assembled and be accessible to install the wires/control cables

I will throw something together in the morning

[Colin J.S]

30 minutes ago, flash22 said:

If you look at the back of the  base there are 3 holes what the screws go in to these are also heat stakes that hold a cover on, the base its self should be hollow, it has to be assembled and be accessible to install the wires/control cables

I will throw something together in the morning

Yeah I know 

[flash22]

Sorry, i meant the actual upright that bolts to the car

[Colin J.S]

13 hours ago, flash22 said:

Sorry, i meant the actual upright that bolts to the car

Here are the 2 mirrors from the back so you can see (hopefully) the mounting holes, I cant see a way to mount the new ones lower down as you suggested ...I also had to cut the back of the IQ one so it will sit flat to the car 

[flash22]

Can you get the mirror housing off the Aygo base ?? You should be able to just undo the 3 screws on the IQ one to take off the housing, i don't see why the IQ mirror housings will not fit the Aygo base

https://www.megazip.net/zapchasti-dlya-avtomobilej/toyota/iq-38281/nuj10-56579/nuj10r-bgfnww-925501/mirror-17907266

[Colin J.S]

1 hour ago, flash22 said:

Can you get the mirror housing off the Aygo base ?? You should be able to just undo the 3 screws on the IQ one to take off the housing, i don't see why the IQ mirror housings will not fit the Aygo base

https://www.megazip.net/zapchasti-dlya-avtomobilej/toyota/iq-38281/nuj10-56579/nuj10r-bgfnww-925501/mirror-17907266

Ths is the Aygo mirror fully taken apart